A light switch for fast electronics

Extremely brief and intense laser pulses can switch fused silica (quartz) from an insulator to a conductor and back again within quadrillionths of a second.

December 14, 2012

Semiconductor components form the backbone of all kinds of electronic equipment. The speed with which these components can switch currents on and off is one of the critical quantities for describing the power of computers, for example. The fastest silicon-based transistors presently work at clock speeds of a few billions of switching cycles per second – a single switching process thus lasts about one ten-billionth of a second. A research team lead by Ferenc Krausz, Director at the Max Planck Institute of Quantum Optics (MPQ) in Garching and head of the Attosecond Physics Lab has successfully demonstrated that, under certain conditions, ultrashort light pulses of extremely high intensity can induce electric currents in otherwise insulating dielectric materials (Nature, AOP, 5 December 2012) and the change in the materials properties can be switched on and off at ten thousand times the speed of conventional electronics.

Semiconductors owe their name to their particular property of conducting electrical current only under certain circumstances. In the normal state, they behave like insulators, i.e. they do not conduct current. However, when a small electrical voltage is applied to them, they act like conductors. The electric field transfers energy to the electrons that are bound in the ground state to their atoms and mobilises them. Then they are able to follow an externally applied voltage and form an electrical current.

By rapidly switching the external voltage on and off, an electrical current can be switched in a semiconductor. In contrast, the electrons in insulators – also called dielectrics - are bound so tightly to the atoms that this is usually not possible.

A research team headed by Agustin Schiffrin at the MPQ irradiated fused silica (quartz glass, an insulator) with extremely brief laser pulses and thereby created such high local electrical fields in the interior of the material in which the electrons originally bound to (and held by) the atoms could be mobilised and formed a current.

Ultrashort laser pulses render dielectric conductive

The fused silica sample used in the experiment was cleaved to form a small prism with an extremely sharp tip and coated on two sides with gold, serving as electrical contacts. At the tip a tiny slit between the gold contacts permits direct access to the fused silica. The researchers irradiated the fused silica with extremely short laser pulses that consist of only about one-and-a-half cycles of the light wave. “If the pulses were longer, they would deposit so much energy into the material that it would be destroyed”, explains Tim Paasch-Colberg, the doctoral candidate working on the experiment.

Light consists of an oscillating electric and magnetic field. The extremely brief and intense pulses used in the experiments carry an electric field that increases from moderate values to more than ten billion Volts per metre extremely rapidly, within only a few femtoseconds. This field strength represents a field one hundred thousand times stronger than the field in a flash of lightning.

In their experiment, the physicists in Garching proved that the electrons were freed by this strong electric field within less than a half cycle of the laser light. This means that the insulator becomes a conductor within a mere femtosecond. “These measurements did not resolve the question of whether the conductivity can be turned off again just as fast”, says Tim Paasch-Colberg. Only this property transforms a component into a switch with which electrical signals can be controlled and processed.

With attosecond pulses, the process can be recorded “in slow motion”

In a second experiment, the research team headed by Martin Schultze investigated the question of how fast the conductivity can be turned off. The physicists transformed the fused silica again from an insulator into a conductor with an ultra-short laser pulse. Then they sent a series of extremely short-wavelength UV-laser pulses of only a few tens of attoseconds in duration (an attosecond corresponds to 10-18 seconds, or a billionth of a billionth of a second) with varying time-delays through the fused silica sample and recorded by how much each of these pulses were absorbed by the material. The degree of absorption depends specifically on which of the two states – insulating or conducting – the material is in. “The technique can be compared to recording a fast process with a high-speed camera and subsequently studying it in slow motion”, explains Elisabeth Bothschafter, the doctoral candidate working on this second experiment.

The results of this second experiment proved that the modification of the insulator by the powerful light field can indeed be reversed on the timescale of a few femtoseconds. The transformation from an insulator into a conductor and back again can be arbitrarily repeated and is therefore reversible. “It was surprising for us to see that basic material properties can be changed at optical frequencies.””, says Martin Schultze.

Future research will show whether fused silica can be employed in a switch operating at light frequencies. The intense ultra-short-cycle lasers necessary to achieve this are presently much too large. “We hope that these results will motivate many other labs and groups worldwide to join us in further investigations”, says Ferenc Krausz. “We would like to explore as soon as possible the feasibility of this promising development towards accelerating electronic switches to light frequencies.”

TB/PH

 

Go to Editor View